穎鑫電子科技有限公司規格書
SPECIFICATION |
| |
| DESIGNATION 系列:輕觸開關 |
| MODULE NO. 型號: SK-12F23-G6 |
| 1. RATING 額定值: 0.3A DC 50V |
| 2. CIRCUIT 回路: 1P 2T |
| 3. TIMING 切換類型: S(SHORTING)/ Non-shorting |
4. STANDARD TEST CONDITIONS SHALL BE 5 TO 35℃ IN TEMPERATURE AND 45 TO 85%
IN HUMIDTY. |
| 溫度5-35℃,濕度45-85%標準狀態下測試. |
| 5. OPERATING TEMPERE RANGE -- 10 TO 60℃ |
| 溫度-10~60℃環境內使用. |
| ITEM 項目 |
TEST CONDISTION 測試條件 |
PERFORMANCE 規格 |
| 6. ELECTRONICAL PERFOORMANCE 電氣性能 |
| 6.1 |
CONTACT
RESISTANCE
接觸阻抗 |
Being measured at 1kHz small current contact
resistance meter.
在1KHz小電流下測量 |
30MΩ max.
30毫歐以下. |
| 6.2 |
INSULATION
RESISTANCE
絕緣阻抗 |
Measurements shall be made following application
of DC 500V potential across terminals and
across terminals and frame for 1 minrte.
在端子之間和端子與殼之間加DC 500V 條件下,
持續1分鐘測量. |
100MΩmin..
100毫歐以上 |
| 6.3 |
WITHSTAND
VOLTAGE
耐電壓 |
AC 500V(50Hz or 60Hz)shall be applide across
terminals and acoss teminals and frame for one minrte
在端子之間和端子與殼之間加AC 500V
(50Hz或60Hz)條件下,持續1分鐘表測量. |
There shall be no breakdown.
無擊穿現象出現. |
| 7. MECHANICAL PERFORMANCE 機械性能 |
| 7.1 |
OPERATING
FORCE
動作力 |
MEASURE AT THE POINT 3mm FROM THE TIP
OF THE ACTUATOP （KNOB）
在距離推桿前端3mm作測定點. |
250gf±50gf |
| 7.2 |
TERMINAL
STRENGTH
端子強度 |
A static force of 500gf being applied in one direction
the tip of the terminal for 1 minute.
一個500克之靜電負荷施加于端子頂部的一個方向
持續1分鐘. |
There shall be no sign of
damage mechanically and
electrically.
無任何跡象顯示機械及
電器性能之損壞. |
| 7.3 |
ACTUATOR
STRENGTH
推桿強度 |
A static load of 1kgf being applied in one
direction of actuator for one min.
一個1公斤靜負荷施加于推桿之一個方向持續
1分鐘. |
The defromation shall not be
extrene and the actuator shall
machanically work normally
推桿無變形,可以正常操作 |
QQ客服-陳心龍 